Plate heat exchanger

porducts list

Other Food [1]
Waste Management [1]

contact datails

WUXI SHUANGSHENG PETROCHEMICAL EQUIPMENT CO.,LTD

the town of Fishing Bridge Xuelang Binhu District, Wuxi City, Jiangsu

0510-85181788
013901513502

Plate heat exchanger


company	WUXI SHUANGSHENG PETROCHEMICAL EQUIPMENT CO.,LTD
Categories	LED Displays
Update	2011-03-14
Original Region	China
prev 1 2 3 4 5 6 7 8 9 10 next

Plate heat exchanger

This equipment is a highly efficient heat transfer equipment for gas - gas, liquid - liquid, gas - liquid convection heat transfer, as well as for steam condensation and liquid evaporation. The product has a high heat transfer efficiency, self-cleaning ability dirt, energy saving, small and inexpensive to use and reliable. Is widely used in pharmaceuticals, solvents, chemicals, rosin, dyes, food industry, heat exchange, waste heat recovery.

Plate heat exchanger design features:
一、High efficiency heat exchanger
Heat transfer coefficient usually ranging from2000—5000kcal/m2hr℃ ,Shell and tube heat exchanger than the 3-5 times higher
二、Compact
Film due to heat transfer in close order, and other forms of heat exchanger compared to a smaller area or space,
三、Easy maintenance
Plate tightly assembled together, ready to open the maintenance and cleaning
四、Life long
Plate can be used 0.6-1.0 mm 304.316.316L stainless steel or titanium alloy sheet made repression can be a variety of corrosion-resistant media.
5, assembly and flexible solution without strings
heat transfer area may be different according to the user requirements of assembled machine, such as the initial power to change through changes in the plate can be. In addition, because access is a two-plate sealed, grain vent steam flow Daoxing into what may be the security zone, thus avoiding the possibility of two kinds of media collusion. "

Plate Heat Exchanger Technical

Type	BR08	BR15	BR20	BR25	BR30	BR40	BR55
Monolithic heat transfer area	0.08M2	0.15M2	0.20M2	0.25M2	0.30M2	0.41M2	0.55M2
Dimensions	200×600	785×275	955×325	955×325	990×390	1210×400	1400×490
Plate spacing mm	2.6	2.6	5.0	3.5	5.0	3.6	3.8
Hole diameter mm	40	50	65	65	80@	100	125
Design pressure	1.2Mpa	1.2Mpa	1.0Mpa	1.2Mpa	0.8Mpa	1.2Mpa	1.0Mpa
Design temperature()	150	150	150	150	150	150	150
Maximum flow	20t/h	30t/h	60t/h	60t/h	100t/h	100t/h	200t/h

Caution:
one, first check the pre-boot the entire pipe connection system as well as the fluid required by the form of import and export links, open the boot due to the first low-temperature low-pressure valve , and then open the high-temperature high-pressure fluid valves. Shutdown to close the high-temperature high-pressure fluid valves, and then close the low-temperature low-pressure fluid valves.
2, plate heat exchangers used in liquid - liquid exchange, do not need to set up exhaust devices, steam - gas exchange and low-velocity high-viscosity fluids should be set up in the piping system exhaust valves, lose steam trap improve the efficiency of heat transfer units.
3, plate heat exchangers over a long period of continuous operation, due to fluid accumulation in the sediment sets the surface of the plate, increasing the thermal resistance, so that reduces heat transfer efficiency, maintenance staff carry out regular cleaning and maintenance.
4, maintenance time, such as the need to replace gaskets, first plate with acetone or ethyl acetate cleaned, and then each slot in the plate and sealing mat coated with adhesives, which will be a little dry gasket embedded, such as tank, surrounded by uniform pressure level, a few hours can be assembled.

Gasket Material:

Applicable to medium and temperature

NBR: Non-polar oils, mineral oils, lubricants, silicone oil and so on. -30 +130

EPDM rubber: wate